Avital LX L • 1-Way Remote Start System Keyless Entry and 2 Remote Transmitters Remote Start Vehicle System with two transmitters • Panic and. Buy Avital Avistart Remote Auto Car Start Starter & Keyless Entry System L at Once an Avital Remote Start package is purchased, you can either take it to a mechanic to have the system installed or you can do it yourself. If you decide.

Author: Salkree Zulkishura
Country: Botswana
Language: English (Spanish)
Genre: History
Published (Last): 28 May 2004
Pages: 269
PDF File Size: 10.20 Mb
ePub File Size: 8.21 Mb
ISBN: 932-7-17059-443-8
Downloads: 55913
Price: Free* [*Free Regsitration Required]
Uploader: Gular

Comments to this Manuals Your Name. Start the vehicle with the key. Be sure to keep the clips that hold the dash panel trim on for later use. If this does not work, a tach wire should be used.


The two red heavy gauge input wires on the relay xvital should have solid connections. Page 47 The vehicle will start and run only for about 10 seconds.

Remote Control Learn Routine Remote control learn routine The system comes with two transmitters that have been taught to the receiver.

This product is intended for installation by a profes- sional installer only!

Operation is subject to the fol- lowing two conditions: This can be done using a wire tap. In this step, you will first need to disconnect the ignition switch wiring.

The remote start will be disabled or shut down any time the brake pedal is depressed. Feature Default Optional settings setting Remote start runtime 12 minutes minutes Diesel start delay Neutral Safety Switch Interface Neutral safety switch interface Some vehicles do not have an electrical neutral safety switch. When the dou- ble pulse unlock feature is turned on, the BLUE 3 wire will supply two negative pulses instead of a single pulse.


Press and the Program switch. It is the default RPM-sensing method for new remote start systems. Page 40 When programmed to the latched output the status will only stay active for 10 minutes. By pressing ‘print’ button you will print only current page.

You can also narrow down these results by choosing an appropriate category to the left. Page 7 tion immediately and consult with the user to fix the problem immediately. Simply hold down the button for one second and secure it out of the way.

Next, use the trim tool to remove the dash panel trim and the trim above the ignition switch.

How to Install an Avital 4103 Remote Start

Avtial The starter cranks for six seconds but does not start. Always use the Vehicle Safety Check section of this guide to verify that the vehicle cannot be started in ANY drive gear and that the override switch is functioning properly.

To buy any products needed for this DIY project on eBay, simply type the name of the product you’re looking for in the search bar and browse the many buying options.

Use the following learn routine to add transmitters to the sys- tem. When programmed to the latched avitxl the status will only stay active for 10 minutes. Make sure the hood is closed and no other shutdown circuits are active. This lets you start your car from inside a house or other building so your car is the perfect temperature when you get in. This makes it possible to directly interface with double pulse vehicles without any extra parts.

Avital – Products

Try program- ming the unit for low voltage reference. Heavy Gauge Relay Interface Heavy gauge relay interface The heavy gauge wires are used to energize high current circuits in the vehicle. Don’t show me this message again. To do this, remove two screws underneath the steering column to take off the steering column’s cover.


Turn the ignition off. Be sure to then switch the Neutral Safety Switch to the “on” position, as this remote start will not work without it being on. This resets features all of the security system to the factory default settings. Table of Contents Add to my manuals Add. The Program switch can now be re- DRW leased.

Avital 4103 Installation Manual

To connect the wires, first cut the insulation of the proper wires with the X-Acto knife. Be sure not to touch the pink and white 2nd accessory wire, as this does not need to be connected.

Feature Descriptions Feature descriptions The features of the system are described below with default settings in bold. Use it to change the output pulse duration for vehicles that require a longer pulse for the horn to honk. Turn the ignition on and then off. This product is designed for fuel-injected, automatic transmission abital only. The Program push-button switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. Set the emergency brake. Scrape away any paint and use a factory bolt or make your own ground with a self-tapping screw and a star washer.