Lexmark Edn Manual Online: Paper Input And Duplex Sensor Assembly Removal. 1. Remove the right side cover. See 2. Remove the duplex. See 3. Office Manuals and free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Lexmark ED Service Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. This is the Service Manual for Lexmark.

Author: Akibar Tojagis
Country: Barbados
Language: English (Spanish)
Genre: Travel
Published (Last): 2 December 2018
Pages: 209
PDF File Size: 2.68 Mb
ePub File Size: 19.68 Mb
ISBN: 223-5-86741-781-6
Downloads: 61814
Price: Free* [*Free Regsitration Required]
Uploader: Grogor

To replace the photoconductor kit: E260vn both the front and rear doors. Print Lexmarkk Page Protect Description Sets the amount of time in minutes the printer waits after a job is printed before it goes into a reduced power state Note: Too many options attached Meaning This message indicates that to too many flash options have been attached. Page Page – Right side cover assembly removal Page Page – Top cover assembly removal Page Page – Transfer roll removal Page – Wear strip tray 1 and sheet tray Page Page – Right side cover assembly removal Page Page – Top cover assembly removal Page Page – Transfer roll removal Page – Wear strip tray 1 and sheet tray Page 40 Load media in Tray 1 or Tray 2 Meaning The printer is out of print media at the e260en source.


2e60dn Reconfigure the device using DHCP. Engine detected no gap at the manual feeder sensor, attempted to open the gap by stopping the feed rolls, but no trailing edge was ever seen at the input sensor. For other countries or regions, visit the Lexmark Web site at http: PageTilt the rear cover, and remove.

Disconnect all cords and cables from the printer before moving it. Page 42 If you mznual loading a longer size of paper like A4 or legal, squeeze the length guide tabs and slide the length guide backwards to the position for the length of paper you are loading.


Lexmark E260dn User Manual

Disconnect the spring E from the cylinder. Use a pencil to mark the screw locations of the old printhead on the metal frame.

Door Mount RemovalDoor mount removal Open the front cover. Temperature information Ambient temperature Selecting A Location For Mamual Printer Warranty information Selecting a location for the printer When selecting a location for the printer, leave enough room to open trays, covers, and doors.

Lexmark Printer E User Guide |

Do not remove trays while a job prints or when the Busy light sequence appears on the printer control panel. Page 33 Cartridge error – On – On Front door is open – On Interpreting the printer control panel lights What you can do Press and release either to return to the Ready state. After obtaining a properly adjusted image on the paper, tighten all three screws. Paper And Specialty Media Guide Single-sided paper labels designed for laser printers are supported for occasional use.

USB port Parallel port Printer power cord socket Power switch Security slot Configured models The following illustration shows the printer configured with an optional or sheet drawer: Large jobs do not collate It also provides instructions on how to navigate through the configuration menus to select and save new settings.

Page 95 Page 96 Page 97 Page 98 – Clearing jams behind the photoconductor The photoconductor kit and toner cartridge form a unit. Lexmark has found no reason to discourage the use of today’s recycled office papers, but generally the following property guidelines apply to recycled paper. Envelope is the factory default setting.

Open the duplex jam door just far enough to pull out the ACM pick tires. Blank Pages If the printer still prints blank pages, it may need to be serviced. These are accessed through the driver.


Bezel RemovalBezel removal Open the front access door. Using the manual feeder The manual feeder is located inside the manual feeder door of the printer and can feed only one sheet of paper at a time. Action Wait for the message to clear. Use envelopes that lie flat when individually placed on a table facedown.

Page 38 The photoconductor kit is full and must be replaced. PageAssembly 5: Disconnect the cable A from the controller board, and remove the two screws B holding the fan to the right side frame.

Service Error Codes Hot roll timed out in trying to reach the final lamp detection temperature. Press and release Continue twice quickly to display the secondary error code light sequence. Pull the photoconductor kit and toner cartridge together as a unit out of the printer by pulling on the toner cartridge handle. Remove the inner shaft lock C. Printer configurations Basic model The following illustration shows the printer front with its basic features or parts: Load the letterhead with the design placed facedown.

If you purchased a multifunction printer MFP that scans, copies, and faxes, you may need additional furniture. Also look at the printer preferences: Ordering A Photoconductor Kit Ordering a photoconductor kit Depending on your printer model, the printer issues a message or a light sequence to let you know the photoconductor kit is near its end of life. Remove the three screws B from the left door mount.